G-Switch 東莞品贊電子科技有限公司
|
SPECIFICATION
規格書
|
Designation 品名:
|
USB插座
|
Model No. 型 號:
|
USB AF 90度沉板有卷邊
|
1. Rating額定值:
|
DC 48V 0.2A
|
2. Operation temperature range 使用溫度範圍:
|
-20℃~+70℃
|
3. Preservative temperature range 保存溫度範圍:
|
|
4. Construction dimension
結構尺寸:
|
Apply to the appended drawing:
符合附加圖紙
|
Item 項目
|
Test condition 測試條件
|
Specification規格
|
5. Electrical characteristics電氣性能
|
5A
|
Contact Resistance
接觸阻抗
|
Being measured at 1KHz small current
contact esistance meter.
在1KHZ小電流下測量.
|
30mΩ max.
30毫歐以下.
|
5B
|
Insulation Resistance
絕緣阻抗
|
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO
FOLLOWING PORTIONS AFTER WHICH
MEASUREMENT SHALL BE MADE:
(1) BETWEEN BODY AND CONDUCTOR
(2) BETWWEN CONDUCTORS NOT TO BE
CONTACT
輸入:500V DC 電壓1分鐘,按以下接觸方法測試:
(1)接觸端子之間
(2)膠座與排腳之間
|
100MΩ min.
100兆歐以上.
|
5C
|
Withstand Voltage
耐電壓
|
AC AC 500V IMS(50Hz) FOR 1 MIN TRIP CURRENT:
0.5mA
(1)BETWEEN BODY AND CONDOCTOR
(2) BETWEEN CONDUCTORS NOT TO BE CONTACT
輸入AC 500V(50HZ)電壓,1分鐘感應電流0.5mA,接以
下接觸方法測試:
(1)排腳相互之間
(2)排腳與外殼之間
|
WITHOUT DAMAGE TO
PARTS ARCING OR
BREAKOOWN ETC
沒有絕緣破壞等異常
|
6. Mechanical characteristics 機械性能
|
6A
|
Insertion and
Extraction force
插拔力
|
插入力度:
MEASUREMENT SHALL BE MADE AFTER
CONNECTING AND DISCONNECTING USING
STANDARD PLUG GAUGE 3 TIMES.
依據標準的PLUG GAUGE 做出3次撥插后測定
拔出力度:
MEASUREMENT SHALL BE MADE AFTER
CONNECTING AND DISCONNECTING USING
STANDARD PLUG GAUGE 3 TIMES.
依據標準的PLUG GAUGE 做出3次撥插后測定
|
(0.7kg~4kg)
|
6B
|
Terminal Strength
端子強度
|
A STATIC LOAD OF (300gf)SHALL BE APPLIED
TO THE TIP OF TERMINAL FOR 1MIN. IN ANY
DIRECTION.
在任意一個方向的先端加上(300gf)力度測,時間為
1 分鐘。
|
THERE SHALL BE NO DAMAGE
TO THE TERMINAL SUCH AS
CRACKS, LOOSENESS OA PLAY
ELECTRICAL AND MECHANICAL
CHARACTERISTICS SHALL BE
SATISFIED
在排腳中沒有裂開,松動等異常。
滿足于機械,電氣性能。
|
7. Durability 耐久性
|
7A
|
Soldering test
可焊性試驗
|
THE TOP OF THE TERMINALS SHALL BE DIPPED
2mm IN THE SOLDER BATH OF 230±5℃ FOR
3±0.5 SECONDS.
端子頂部被浸入錫焊池中1mm 深,溫
度為230±5℃,時間為3±0.5 秒。
|
THE AREA OF SOLDERING.
SHOULD BE OVER 75%.
焊接面積要有75%以上。
|
7B
|
Resistance to
soldering heat
耐焊接熱
|
SOLDER BATH METHOD:
SOLDER TEMPERATURE 260±5℃ IMMERSION
TIME 3±0.5 SEC IMMERSION DEPTH UP TO THE
SURFACE OF THE BOARD THICKNESS OF
PRINTED WIRING BOARD 1.6mm DIMENSIONS
OF COMPONENT HOLES IN THE PRINTED
WIRING BOARD SHALLBEING ACCORDANCE
WITH THOSE
SPECIFIED IN THIS SPECIFICATION.
焊爐焊接的時候溫度控制在260±5℃,過
爐時間3±0.5 秒,于(基板)厚度為1.6mm
|
WITHOUT DEFORMATION OF
CASE OR EXCESSTVE
LOOSENESS OF TEMINALS
ELEXTRICAL
CHARACTERISTICS SHALL BE
SATISFIED.
本體無變形、能滿足于機械、電氣
性能。
|
Remark
備 註
|
G-Switch 東莞品贊電子科技有限公司
|